​ Perform regular maintenance on the filters to keep your vacuum's suction power optimal.

To prevent damage, rinse filters with water ONLY. DO NOT use soap. Allow filters to air-dry for at least 24 hours before reinstalling them to prevent liquid from being drawn into electric parts.

The Pre-Motor Filters should be washed once a month.
The Post-Motor Filter should be washed once every 9 months.

1. Insert Wand into Floor Nozzle.
2. Insert Handheld Vacuum into wand.
3. Snap the Accessory Holder onto the wand, then place accessories in the holder. Ensure all connections click securely into place.

0 - Press the power button to begin vacuuming.
To turn off power, press button again.

I - Bare Floor/Small Area Rugs
The brushrolls spin slowly to clean bare floors and small area rugs.

II - Carpet
The brushrolls spin faster to pick up debris below the surface of your carpets.

To clean floors, place foot on floor nozzle and tilt handheld vacuum back.

Above-Floor with Wand
Detach the nozzle for more reach to clean baseboards, ceiling fans, window sills, and​ other hard-to-access areas. To disconnect the wand, stand the vacuum upright. Step​ on the foot pedal on the side of the nozzle, then pull the wand out of the nozzle.

Above Floor Handheld
To use in Hand Vac mode, press the Wand Release button and lift the handheld vacuum off the wand. Great for cleaning stairs, furniture, and countertops.

Press the unlock latch on the back of the wand, then adjust the angle.
Adjust the wand to a lower angle to easily clean under furniture.

Empty the dust cup each time you vacuum and periodically during cleaning, when debris in the dust cup reaches the MAX fill line.

Press the wand release button and lift the handheld vacuum off the wand. To remove the dust cup from the handheld vacuum, squeeze the two Dust Cup Release buttons at the​ same time and pull out the dust cup.

Hold the dust cup over the trash. Press the Empty button and pull the dust cup open.

Perform regular maintenance on the filters to keep your vacuum's suction power optimal.

To prevent damage, rinse filters with water ONLY. DO NOT use soap. Allow filters to air-dry for at least 24 hours before reinstalling them to prevent liquid from being drawn into electric parts.

The Pre-Motor Filters should be washed once a month.
The Post-Motor Filter should be washed once every 9 months.

Check handheld
Remove the handheld vacuum from the wand and check all dust cup intake openings.

Check wand
Detach the wand and check it for blockages.

Check Floor Nozzle
Detach the wand, then remove the Soft Roller.
Tilt the floor nozzle tube back and check openings for blockages. Reinsert Soft Roller until it clicks securely into place.
Remove any blockages or debris from the floor nozzle debris intake

If you notice any hair wrap, continue vacuuming and the Self-Cleaning Brushroll​ will automatically remove it. If some hair wrap remains after continued use, remove​ the brushroll cover from the bottom of the nozzle and use scissors to carefully cut away​ the hair.

To remove the cover, use a coin to turn the locks counterclockwise. Lift off the cover​ and remove any debris or hair wrap. Check the Debris Intake and clear away any dirt or​ blockages.

To close the cover, push down until it clicks into place, then turn the locks clockwise​ until closed.

 Granite Grey/Rose Gold

4.8kg

 450W

 Carpets and hard-floors

10m

(Refer to Maintenance section for more information.)
Check filters to see if they need cleaning. Follow instructions for rinsing and drying the filters before re-inserting in the vacuum.
Dust cup may be full; empty dust cup.
Check hose, hose connections, nozzle, and accessories for blockages; clear blockages if required.
Remove any string, carpet fibres, or hair that may be wrapped around the brushrolls.

Turn off unit to disengage the brushrolls. Move switch to Hard Floor setting to turnon the slow brushrolls, which is optimal for bare floors and area rugs.

• Suction is powerful. Take care when vacuuming area rugs or rugs with delicately sewn edges.

If Brushroll Indicator Light on the floor nozzle turns red, the brushroll and/or Soft​ Roller have stopped spinning. Immediately turn off and unplug vacuum.
Disconnect​ the nozzle and remove blockage, then reconnect and turn vacuum back on.
With the power on, recline the handle, which will automatically turn on the brushrolls.