Solid Green: The brushroll is spinning and working as it should.
Solid Red: There is a jam in the brushroll area. Turn your vacuum off and remove any blockages.
Flashing Red*: The motorized floor nozzle is overheating. Turn your vacuum off and wait 45 minutes for it to cool down.

* See Troubleshooting section for further instructions.

1. Insert Wand into Floor Nozzle.
2. Insert Handle into wand.
3. Place Pod onto wand and slide down to connect.
4. Connect Hose into back of pod, until it clicks into place.

For proper operation, ensure all parts are firmly clicked into place.

Press the Power button to turn the vacuum on or off.
Slide the selector switch to the appropriate surface setting:

• Hard Floor
  The brushrolls spin slowly to pick up fine dust and large debris on hard floors.
• Carpet
  The brushrolls spin faster to pick up debris on and below the surface of your carpets.
• Suction Control Slider
  Increase or decrease suction as needed. Slide to MIN to reduce suction and increase maneuverability on carpets. Slide to MAX to increase suction on bare floors.

• Upright
  To engage brushroll, turn power on, select a surface setting, then step on floor nozzle and tilt handle back.
• Lift-Away
  Press Lift-Away Button to lift pod off motorized floor nozzle. You are now ready to clean those hard-to-reach places.
• Above Floor
  Press the Handle Release Button to detach the handle to clean above-floor areas. Insert accessories directly into handle.
• Above Floor Extended Reach
  Press the Wand Release Button to detach the wand to clean with more reach. Insert accessories directly into wand.

• Pull up on Dust Cup Release Latch on the handle and lift dust cup off pod.
• Hold dust cup over a trash bin and press the empty-release latch on the bottom to empty dust and debris into trash.
• Press Top Empty Release Latch to access dust screen and remove built-up debris as​ necessary.

Regularly clean and replace the filters to keep your vacuum's suction power optimal.
To clean filters, rinse with cold water ONLY to prevent damage from cleaning chemicals. Allow​ all filters to air-dry for at least 24 hours before reinstalling them to prevent liquid from being​ drawn into electric parts.

• Pre-Motor
  With the dust cup removed, take out the foam and felt filters and rinse them with​ water only.
  Tap loose dirt off filters between washes as needed.
  CLEAN PRE-MOTOR FILTERS EVERY 3 MONTHS.
• Post-Motor (HEPA)
  To access the HEPA Filter, pull the latch under the filter cover and take off the cover.
  Remove the HEPA filter and rinse it with water only.
  CLEAN HEPA FILTER AND POST MOTOR FILTER EVERY YEAR.

Follow the previous instructions for removing filters. The pre-motor filters should be replaced every​ 2.5 years. The post-motor HEPA filter should be replaced every 3 years.

The self-cleaning brushroll automatically removes hair wrap.
If some hair or debris remains after​ continued use, remove the cover to access the brushroll.
Using a coin, turn locks counterclockwise, then open the cover to access Brushroll.​
NOTE: Cover will open but is not completely removable.

DuoClean technology features a bristle brush to deep-clean carpets, and an additional soft​ brushroll to pull in larger particles and directly engage floors for a polished look.

To remove the Soft Roller, slide the Eject Roller button on the floor nozzle. Tap loose debris off the Soft Roller. Use a dry towel to wipe it clean, and to remove any debris caught in the teeth behind the Soft Roller.
Hand-wash the Soft Roller as needed. Use only water, and let it air-dry completely for at least​ 24 hours.
Reinsert the Soft Roller and press it in until it clicks securely into place.

 Navy/Orange

6.5kg

750W

1.6metres

8 metres

 Carpets and hard-floors

10m

• Check filters to see if they need cleaning. Follow instructions for rinsing and air-drying the​ filters before reinserting in the vacuum.
• Dust cup may be full; empty dust cup.
• Check hose, hose connections, nozzle, wand, pod, and accessories for blockages. Clear any​ blockages found.
  ​ (Refer to Checking for Blockages section for more information.)
• If any hair, string, or carpet fibers are wrapped around the brushroll, extend cleaning time to​ allow the self-cleaning brushroll to remove them.
  – If some hair or fibers remain wrapped around brushroll after continued use, remove the​ floor nozzle cover and carefully cut debris with scissors and remove from brushroll. See​ Cleaning the Brushroll section for more information.

Make sure selector switch is set to Hard Floor.
Suction is powerful. Take care when vacuuming area rugs or rugs with delicately sewn​ edges.
To minimize suction, slide selector switch to Thick Carpet/Area Rug.

• If the Brushroll Indicator Light turns red, immediately turn off and unplug the vacuum.
• Remove pod from floor nozzle. Clear any blockages or debris from the brushroll and​ nozzle. (See Checking for Blockages & Maintaining Brushroll.)
• Close the brushroll cover and​ reconnect the pod to the floor nozzle.
• Plug in the vacuum and turn on the power.​ With the power on,
• recline the handle, which will automatically turn on the brushroll.
• Ensure that the selector switch is set to Carpet/Low Pile for brushroll to spin.

This vacuum is equipped with a motor-protective thermostat. If your vacuum overheats, the​ thermostat will automatically turn the suction motor off.
Perform the following steps to restart​ the thermostat:

1. Turn vacuum off and unplug it.
2. Empty dust cup and clean filters (see Emptying the Dust Cup and Cleaning and Replacing the Filters).
3. Check for blockages in hose, accessories, and inlet openings.
4. Allow unit to cool for a minimum of 45 minutes.
5. Plug in the vacuum and turn on the power.