Shark’s Zero-M™ self-cleaning brushroll delivers non-stop hair removal. If you run over a hard or sharp object or notice a noise change while vacuuming, check for blockages or objects caught in the brushroll. NOTE: Do not be alarmed if there is visible hair wrap on the brushroll at any given time, as it should eventually make its way to the dust cup.

Using a coin, turn locks counterclockwise, then lift the door to access Brushroll.
Clean off any debris on the bristles.
If you run over a hard or sharp object or notice a noise change while vacuuming, check for blockages or objects caught behind the brushroll. Clear away any dust, dirt, or blockages in Debris Intake. To close the cover, push down until it clicks into place, then close the locks with a coin.

1. Insert wand into pod.

2. Insert handle into wand..

3. Attach hose to back of vacuum pod.

4. Attach hose to clip on wand.

5. Insert C-shaped clip onto base of vacuum pod and remove tape.

6. Store accessories on tool storage posts.

For proper operation, ensure all parts are firmly clicked into place.

Solid Green: The brushroll is spinning and working as it should.

Solid Red: There is a jam in the brushroll area. Turn your vacuum off, unplug from the wall and remove any blockages in the nozzle.

Flashing Red: The motorized floor nozzle is overheating. Turn your vacuum off and wait a minimum of 45 minutes for it to cool down.

Your Suction Control slider located on the top of the handle allows you to adjust your suction depending on your floor type. MIN: to reduce suction and increase maneuverability on carpets. MAX: to increase suction on bare floors.

Select surface setting:

O Power Off

I Hard Floor For bare floors and small area rugs.

II Carpet For carpets.

Upright

To engage brushroll, place foot on floor nozzle and tilt handle back

Above-floor handle

Press the Handle Release button to detach the handle from the wand.

Above-floor wand

Press the Wand Release button to detach the wand from the pod

To remove Dust Cup, press button on top of dust cup handle. Tilt dust cup forward, then lift to remove.

Press lower release button to open bottom of dust cup.

To remove collected debris from Lint Screen, press top release button and lift handle to open. Gently brush lint screen to clean.

To reinstall, place bottom of dust cup into pod and then tilt back until it clicks into place

Pre-Motor Filter should be replaced every 2.5 years. The HEPA Filter should be replaced every 3 years.

Using a coin, turn locks counterclockwise, then lift the door to access Brushroll.
Clean off any debris on the bristles.
If you run over a hard or sharp object or notice a noise change while vacuuming, check for blockages or objects caught behind the brushroll. Clear away any dust, dirt, or blockages in Debris Intake. To close the cover, push down until it clicks into place, then close the locks with a coin.

 Pewter Grey Metallic

7.3 kg

H: 80cmW: 30cm D: 34cm

 960W

 213aw

 Carpets and hard-floors

 3 litres

 7.6 meters

 7.6 meters

3.6 meters

Check filters to see if they need cleaning. Follow instructions for rinsing and air-drying the filters before reinserting in the vacuum.
Dust cup may be full; empty dust cup.
Check hose, hose connections, nozzle, wand, pod, and accessories for blockages. Clear any blockages found. (Refer to Checking for Blockages section for more information.)

If any string, carpet fibers, or hair is wrapped around the brushroll, extend cleaning time to allow Zero-M™ technology to remove it. – If some hair or fibers remain wrapped around brushroll after continued use, remove the floor nozzle cover and carefully cut debris with scissors and remove from brushroll. See Cleaning the Brushroll section for more information.

Make sure Power/Surface switch is set to Hard Floor (setting I).
Suction is powerful. Take care when vacuuming area rugs or rugs with delicately sewn edges.

If the Brushroll Indicator Light turns red, immediately turn off and unplug the vacuum. Remove pod from floor nozzle and clear any blockages. Reconnect nozzle, plug in vacuum, and turn on power.
With the power on, recline the handle, which will automatically turn on the brushroll.
that the Power/Surface switch is set to Carpet (setting II) for brushroll to spin.